Bentley Continental Key Fob Troubleshooting Tips
The Bentley Continental is a truly astounding vehicle to drive. Its brushed-metal accents the center stack. Beautiful leather and wood decorate its cabin. Its powerful W12 engine generates a staggering 552 break horsepower.
The Continental key fob is encased with rubber to prevent water from destroying the electronic chip. If it is submerged in pure tap water, it will be fine. However prolonged exposure to saltwater can damage it.
Keyless entry system
The Bentley Continental comes with a keyless entry system that allows you to lock and unlock your car using remote controls. This is a great convenience, and you can cut down on time. There are a myriad of reasons your key fob may stop working. Some of them include the battery being dead or water damage, receiver module issues, and signal interference. In some cases the issue could be caused by a malfunction in the internal chip.
The key fob features rubber seals to prevent water from reaching the electronic chips inside. However the key fob might still be soaked if exposed to salt water or soapy water. This can cause damage to the chip. It is crucial to clean the key fob and allow it to dry completely prior returning the battery. If the keyfob doesn't function after cleaning and drying, it is likely faulty and requires replacement.
The clips made of metal on the battery of your Continental keyfob are what hold it in place, and complete the circuit. Contact problems can occur when the clips have corroded or become loose. Check the battery's contacts to ensure they're clean. Also, ensure that the battery has been properly installed. If you have an extra Continental key, try it to determine if it is working. If the key is damaged, you can reprogramme it with an OBDII scan.
Battery
The key fob contains one small battery that is the size of a coin. If it's dead the remote will not function. This is easy to diagnose and can be fixed in a few minutes. Water can also harm the battery, requiring replacement. The key fob may not work for a number of reasons, including worn-out buttons, defective contacts in the battery, signal interference or an inactive module. It is possible to reset the system by disconnecting the battery with 12 volts for a short period of time. This will allow the system itself to reset itself. First disconnect the negative cable before re-connecting the positive cable.
replacement bentley key inside the Bentley Continental key fob will last for up to four years based on the frequency you use it. The battery is secured by metal clips. The clips must be tight. If they are not tight, the remote won't function correctly.
If the Continental keyfob is exposed to clean water from the tap, it must be dried and cleaned using the use of a paper towel before installing the battery. If the chip is exposed to salty or soapy water, it might be fried. In these cases it is necessary to buy an entirely new key fob.
Water damage
David says there aren't any major mechanical issues on this Continental, apart from a little rust to the wheel trims and surface corrosion that has been exposed to road grit. The boot is roomy and practical, with an original warning triangle strapped to the floor, and the space-saver spare wheel as well as a basic Bentley tools under the false floor.
The chip of the key fob is protected by rubber seals, which will ensure that it functions even if it gets wet. However, prolonged exposure to water could damage the chip, so it's recommended to remove your key fob of your pockets when you go swimming, kayaking or rafting or any other activity where it could be wet.
If the key fob you have purchased has been covered in soapy water from the washing machine or submerged in ocean water at the beach, it may be worthwhile to save it by cleaning the chip with isopropyl alcohol or electronic cleaner. If the key fob is unable to work after re-cleaning and drying, it might be time to replace it. If you're looking for a Bentley Continental key fob, make sure you choose one that is waterproof and factory-paired with your car.
Fault diagnosis
The Bentley Continental keyfob lets you to lock or unlock your vehicle with one click. This is a very convenient system and offers safety and security while driving. There are several things that could be wrong when it comes to your key fob. The most frequent causes are a dead coin battery or signal interference, water damage or a damaged internal chip. If the key fob you purchased isn't working, there are some troubleshooting steps you can follow to identify the problem.
The battery is the first thing you need to check. Verify that the battery has been properly inserted and all metal clips are in the right position. If the clips aren't in a good position, the battery may not get a good connection and will not work effectively. The clips that hold the battery must be free of corrosion and clean.
A car battery that is weak is another reason that causes the key fob not to function. The 12 volt battery in your Continental should be in good condition to communicate with the remote keyless entry system and the rest of the onboard electronics. You should check your fuse and recharge your car battery in the event of a need.
The Bentley Continental key fob sends signals to the receiver module which is located inside the ignition barrel. If the signal is lost it will cause the engine to not start and the alarm will sound. If the Bentley Continental key fob isn't working, you should seek out an expert.